Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N141212
These are the latches that hold the popout frame out.
Application:CORE CHARGE If you would like to order these before sending your old spindles in, please add part this to your order. This is the core charge. Once you send back your old spindles we will refund that amount, providing your spindles are good.
Do you have a lowered beam now? They should have come with a kidney belt and a mouth guard. So, here's the answer. Put lowered spindles on your bug or bus and it will ride like it did stock. The bug spindles come with a 2 1/2" drop and the bus with a 3 1/2" drop. On the king and link bug spindles you can get spindles only or have us install the king and link pins. Those of you with 66, 67 bugs will have to change the outer tie rod end to 68 and later. On the bus spindles they only come with the king pins rebuilt. Also on the bus spindles you will need a tie rod with ends from a 1968-1979 (part number 211 415 801F). This is necessary to give more frame clearance. These spindes are cast not welded. Sold in pairs and some on an exchange basis.
All steering box cores must be sent first, before we can send you a rebuilt one. Our stock on these are so low that we cannot chance people not sending cores back. Your box must be and “F” box for 68-72 or a “ZE” or “ATE” box for 55-67. We cannot use any other cores, so please check that you have a rebuildable box before sending.
For all other cores, you have two options. You can send in your core first to avoid having to pay the core fee up front when ordering, or, you can pay the core charge and when we get your core in we will credit you back. You can choose to have it refunded to your card or you can have it put as credit on your account toward future purchases. When sending your core to us, please include your full name and telephone number.. You may choose to have your specific item rebuilt and sent back to you, but that must be made apparent when you send in your core.
We will call you after we have received and reviewed your cores. Most of the cores we receive are rebuildable, however, there are a few that are not able to be rebuilt. We will let you know when we call you whether yours are rebuildable or not, and figure out the next step.
Some reasons why your item might not be accepted:
Steering Boxes:
- Bent steering shaft 55-62
- Completely rusted, won’t turn
- Peg & worm destroyed
Spindles:
- Worn out king pin housing
- Bent spindle
- Spindle threads hammered, cut, or modified
Ball Joints:
- Bent
- Bearing surface pitted/destroyed
IRS:
- Bearing surface too bent, modified, broken.
There may be an additional fee if your item is damaged, yet salvageable/repairable.
Steering boxes that are not usable will be sent back and you will need to find another usable core before you can purchase a rebuilt box.
Bus (Type 2): 63
No customer reviews for the moment.
Part #: 111953051A
Front Turn Signal Bulb Holder, Fits both sides
Application:Part #: 211857145
Gas Door Rubber Stops
Application:Part #: 211698471C
This kit comes with the o-rings and dust seals to repair your calipers.
Application:Part #: 6611780
Enables you do adjust front to rear brake bias with a twist of a knob.
Application:Part #: 043131599A
This is a smog device.
Application:Part #: 1601103A
Screw in Wheel Studs M14-1.5 commonly found in 5x130 applications
Application:Part #: 6611793
Here are some fitting that might come in handy for your pedal assemblies or steering brakes for off road cars..
Application:Part #: 113611723J
These are the metal brake lines found throughout the car.
Application:Part #: 241817031B
Outer Roof Skin with Sunroof and Skylights
Application:Part #: 6721355RD
Clutch Slave cylinder billet
Application:Part #: T1301155
This is a slick tool for getting your starter bushing out with the engine still in the Bug..
Application:Part #: 111945241D
These are the rear lenses for the tail light, brake light and turn signal light.
Application:Part #: 113141723C
This spring returns the clutch arm.
Application:Part #: 6201551
This filler top was used a lot on the old Manx style fiberglass buggies.
Application:Part #: 113101353BCO
All of our rebuilt cylinder heads are built from non-cracked or non-welded head cores (rebuilt welded heads will usually crack again next to the weld).
Application: