Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These are the metal brake lines found throughout the car.
These are the metal brake lines found throughout the car. We suggest you go buy a 11mm tubing wrench and a tubing bender before you start replacing lines. If you have an extra 11mm box end wrench, you can cut a slot in the box end which will allow you to slip it over the tube. When breaking the metal line loose from the brake hose, use a 17mm wrench on the hose and the 11mm wrench on the metal line. Once you have broken it free, remove the clip that holds the hose. When installing the new line, hand thread the nut into the brake hose and then install the clip and tighten. You will need to take out the driver's seat when replacing the front to rear line because it runs along the tunnel. Cut the old line in half. Unthread both ends, one at the master cylinder and the one at the rear union. Pull it out from the inside of the car. Now make the bends in the new line with the tubing bender using the old line as a pattern. Install the new line from the inside of the car starting with the front. Make sure you have grommets where the line goes through the firewalls. 160mm/6.30"
No customer reviews for the moment.
Part #: 315953161DCL
Bullet Clear Turn Signal Lens
Application:Part #: 6105248
Replacement Seal and Collar for Bolt-in Sand Seal
Application:Part #: 151871373A
This is a sleeve that goes in the front window frame for the guide pins to sit in.
Application:Part #: 113105245FRS
Rear Main Seal, Double Lipped
Application:Part #: GR17X
Generators supply the battery with voltage.
Application:Part #: 113141701C
This shaft holds the throw-out bearing in place.
Application:Part #: 211817215
Headliner Grip Strip to Roofline Perimeter NON Fresh Air or Sunroof Applications, 3 Required per Bus
Application:Part #: 1601104A4
Long Wheel Studs, M12-1.5, Set of 4
Application:Part #: 1B09001BL
These are like the transparent caps, not that great but they look cool.
Application:Part #: 211801371A
A floor support section.
Application:Part #: 025129493A
Oil Breather to Air Filter Hose
Application:Part #: 211953215C
This relay makes the turn signal flash.
Application:Part #: T6401023
Tow Strap w/Hooks, 3.5"wide x 13' long, 10,000lbs capacity. A great idea to keep one of these in your car.
Application:Part #: 6615101
Ball Joint Bolt-On Front Disc Brake kit, Dual Drilled Discs with 5x130 and 5x4.75" patterns
Application:Part #: 111141165A
Also known as a throw-out bearing, this bearing's function is to disengage the clutch.
Application:Part #: 1129610EL
This air cleaner takes the place of a stock air cleaner.
Application:
These are the metal brake lines found throughout the car.