Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
The hood catch is what the pin of the hood latch goes into.
The hood catch is what the pin of the hood latch goes into. Adjusting the hood catch will try your patience. After you bolt it in, tie a wire around the catch lever and leave it hanging out the front. Now slide the cable into the barrel lock. With your finger, pull the lever over until it is half way through the hole or until it starts to kick back the other way. Tighten the barrel lock on the cable at this point. Now close the hood slowly making sure the pin on the hood is going to hit the center of the hole in the catch. If not, don't close the hood. Readjust the catch or the latch until it does, then push the hood close and it should latch. If you are having to slam the hood, you're out of adjustment somewhere. If you can hear the hood catch, try and pull the release and see if it opens. If it does, open it and remove your temporary wire. If it doesn't, try pulling on the temporary wire to release it. If that doesn't work, then you have to cut the handle off to get the hood open. Remember to take your time.
Bug (Type 1): 55-67
No customer reviews for the moment.
Part #: N203011
Washer Hose, Black Rubber, Per Foot
Application:Part #: 1198094BCH
94mm Pistons & Cylinders set with a 82mm Stroke CHINA
Application:Part #: 111941197
This chrome screw holds the head light bucket on.
Application:Part #: 1141024
These are hardend bolts, 10.9 instead of the stock 8.8.
Application:Part #: 1903032CH
These are the three pieces of tin that go on the back of the generator or alternator.
Application:Part #: 113707385W
Rear Bumper Bow, Left, US Style
Application:Part #: 211898002
Bus Ignition, 2 front locking door handles, cargo door (Not Panel) and rear hatch handle all keyed alike, only 2 keys included!
Application:Part #: 311133261A
These o-rings should be replaced whenever you replace a fuel injector, or if they are old and cracked.
Application:Part #: 1109337
These push rod tubes are spring loaded and are great for replacing bent tubes without having to pull the head(s) off.
Application:Part #: 151845521AAM
This seal is for the rear window. This is for a CONVERTIBLE ONLY.
Application:Part #: 1615106C
Replacement Front Brake Rotor 5/205, 12x1.5mm, Swing Axle for Kit 1615100F
Application:Part #: 211698003
Brake Spring Kit, Rear, includes both sides, 8 pieces total
Application:Part #: 1127026PG
Fuel Pressure Gauge, 0-15 PSI, 1 1/2"
Application:Part #: 151871032
This is the outer skin on your convertible.
Application:Part #: 111115451
This rubber collar goes around the dump tube that comes from the generator stand.
Application:Part #: 111998161B
The wiper arms are connected to these shafts.
Application:
The hood catch is what the pin of the hood latch goes into.