Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
This seal goes around the front window.
This seal goes around the front window. To remove the old glass, use a fixed-bladed knife. Stick the knife between the rubber and glass on the outside of the Bug. Now cut the rubber until you feel the point of the knife hit metal. Cut all the way around, until you have cut the rubber in half. Peel the rubber off and slowly push the glass out from the inside. Make sure someone is on the outside to catch the windshield. Install the new rubber with the seam on the top and in the middle. Do not use any kind of lubricant, as it will cause the glass to separate. Wrap a piece of 14 gauge wire in the groove that holds the window to the Bug, overlapping the ends on the bottom at the center. Clean the body area and do any repairs needed. We use dish soap as a lubricant, but only between the rubber and body metal, never between the rubber and the glass. Smear the soap from the lip to the outside edge. At this point, grab a friend to help you. Place the window in the Bug from the outside with the two ends of the wire inside the Bug. Push the window in until the rubber hits the lip. While your friend holds the glass in place from the outside, get into the Bug and pull one end of the wire a little one way and then the other wire a little the other way. Keep doing this until you reach the top. If you miss, push the window out and start over. After the first one youll be surprised how easy it is. If you have a lot of windows to do we offer a tool that makes it even easier. American style has groove for chrome.
Bus (Type 2): 80-92
No customer reviews for the moment.
Part #: 221845285CCL
These window seals are on buses 1968 on.
Application:Part #: 211845225B
Sliding Door Glass with hole, fits either side
Application:Part #: 211845521CAM
This seal is for the rear window.
Application:Part #: 2847105APL
New replacement pop out window frames in polished stainless steel. They look like chrome but wont rust.
Application:Bus (Type 2); 50-67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 221845325B
Seals the side popout windows on buses up to 1967.
Application:Part #: 211837375AGR
Felt Channel Kit, For door windows, both doors
Application:Part #: 224845341CCL
Side Window No Vent Wing, Center or Rear, Left or Right, Fixed or Sliding, Cal Look
Application:Part #: 221845343CAM
These window seals are on buses 1968 on.
Application:Part #: 261845521B
This seal is for the rear window.
Application:Part #: 211845227
Door Stationary Glass
Application:Part #: 221847673A
This is the seal that goes around the vent wing seal that is in the middle or the rear side of your bus.
Application:Part #: 241837465
This seal goes on the back side of the front door vent wing.
Application:Part #: 211837396
Goes between the front window frame and the door base on buses up to 1967.
Application:Part #: N109800
Lower Channel Screws, Secures Lower to Window Frame, does Both Sides
Application:
This seal goes around the front window.
