Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:This seal goes around the front window.
This seal goes around the front window. To remove the old glass, use a fixed-bladed knife. Stick the knife between the rubber and glass on the outside of the Bug. Now cut the rubber until you feel the point of the knife hit metal. Cut all the way around, until you have cut the rubber in half. Peel the rubber off and slowly push the glass out from the inside. Make sure someone is on the outside to catch the windshield. Install the new rubber with the seam on the top and in the middle. Do not use any kind of lubricant, as it will cause the glass to separate. Wrap a piece of 14 gauge wire in the groove that holds the window to the Bug, overlapping the ends on the bottom at the center. Clean the body area and do any repairs needed. We use dish soap as a lubricant, but only between the rubber and body metal, never between the rubber and the glass. Smear the soap from the lip to the outside edge. At this point, grab a friend to help you. Place the window in the Bug from the outside with the two ends of the wire inside the Bug. Push the window in until the rubber hits the lip. While your friend holds the glass in place from the outside, get into the Bug and pull one end of the wire a little one way and then the other wire a little the other way. Keep doing this until you reach the top. If you miss, push the window out and start over. After the first one youll be surprised how easy it is. If you have a lot of windows to do we offer a tool that makes it even easier. American style has groove for chrome.
Bug (Type 1): 50-57
Race: 50-57
No customer reviews for the moment.
Part #: 113847139
This is the plate the cover goes over
Application:Part #: 151845521DCL
This seal is for the rear window. This is for a CONVERTIBLE ONLY.
Application:Part #: 113847129BWH
This little plastic cover goes around the hinge on the rear corner window popout..
Application:Part #: 151845521ECL
This seal is for the rear window. This is for a CONVERTIBLE ONLY.
Application:Part #: 113845101D
These are cut from safety glass as required by law.
Application:Part #: 151845121ACL
This seal goes around the front window.
Application:Part #: 151837626
Vent wing seals on the front doors keep out the elements.
Application:Part #: 113845521JAM
This seal is for the rear window.
Application:Part #: 111845101H
These are cut from safety glass as required by law.
Application:Part #: 151837572D
Front Window Sash, Right, Convertible Only
Application:Part #: 151847352C
These are wedge to seal the coners on the front door and quarter windows, where the metal frames meet the scrapers.
Application:Part #: 113847206
This is the little threaded button that goes through the popout glass and screws to the latch..
Application:Part #: 111837476A
The front door window rolls up and down between these two rubber seals.
Application:Part #: 151845521BAM
This seal is for the rear window. This is for a CONVERTIBLE ONLY.
Application:Part #: 111837475B
The front door window rolls up and down between these two rubber seals.
Application:Part #: 151871349C
This sels the leading edge of the top to the front window frame..
Application: