Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These are the metal brake lines found throughout the car.
These are the metal brake lines found throughout the car. We suggest you go buy a 11mm tubing wrench and a tubing bender before you start replacing lines. If you have an extra 11mm box end wrench, you can cut a slot in the box end which will allow you to slip it over the tube. When breaking the metal line loose from the brake hose, use a 17mm wrench on the hose and the 11mm wrench on the metal line. Once you have broken it free, remove the clip that holds the hose. When installing the new line, hand thread the nut into the brake hose and then install the clip and tighten. You will need to take out the driver's seat when replacing the front to rear line because it runs along the tunnel. Cut the old line in half. Unthread both ends, one at the master cylinder and the one at the rear union. Pull it out from the inside of the car. Now make the bends in the new line with the tubing bender using the old line as a pattern. Install the new line from the inside of the car starting with the front. Make sure you have grommets where the line goes through the firewalls. 325mm/12.8"
No customer reviews for the moment.
Part #: 211609701N
Emergency Brake Cable for applications equipped with Brake Booster
Application:Part #: 112920230
30mm Main Venturi for 40/44 HPMX (EMPI), 44 IDF (WEBER)
Application:Part #: 6501149108FB
Billet Boot Retainer and CV Flange, Set (Boot not included)
Application:Part #: 311721335
This cable pulls the arm that releases the clutch.
Application:Part #: 111903137B
This is the belt that turns the generator.
Application:Part #: 2129040
We've found that dual carbs work better than any single carburator set up.
Application:Part #: 111198461BR
The crankshaft rides in the main bearing.
Application:Part #: 113881316R
These are the cover plates that go on the bottom of the seat frame..
Application:Part #: 241853353
These chrome moldings for American style seals go around the windows and are just for looks.
Application:Part #: 211841091A
Cargo Door Skin, Lower Rear to Waistline
Application:Part #: 141857681A
Black Formed Plastic Dash Top Cover includes Adhesive (7" Vent)
Application:Part #: 1823731
This seal clips on the hood instead of the body.
Application:Part #: 6129650593BK
Outerwear pre-filters feature a patented; Micro Mesh nylon filtration system that stops sand and dirt before it gets to your air cleaner element.
Application:Part #: 2863620B
This handy basket hangs from the vent slots to allow you to finally have the cup holder you've always dreamed of. The front spring loaded pocket is a nice place to store your cell phone, or maybe to hold your registration for when the cops pull you over for going too slow. Available in black and white.
Application:Part #: 021101107
Bushing, damper on Main Stud (6 Required)
Application:Part #: 2251003
Single quiet muffler and header, non EGR
Application:
These are the metal brake lines found throughout the car.
