Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These shims set the endplay of the crankshaft.
These shims set the endplay of the crankshaft. It is very important that you get this right. The endplay should be between .003" and .005". Too loose and you will beat out the rear main bearing, too tight and the flywheel will try to grab the rear main bearing and spin it. If you are going to use old shims, make sure they are not cupped. Flex them one by one to see if they pop; if they do, they're cupped. Note: The way to set the endplay is to leave out the flywheel seal and o-ring. Find three .010" shims; install the three shims and bolt on the flywheel. Torque the flywheel to 250 ft. lb. Using a dial indicator mounted on the flywheel with the needle against the case, push the flywheel back and forth to get a reading. If you have too little or too much then take the flywheel off and figure out what you need to add or subtract to come up with the correct endplay. You may need to take out a shim(s) and add a thicker one(s). You must have a total of three shims; no more no less. After you get the correct thickness, install the seal and o-ring.
Bug (Type 1): 66-79
Bus (Type 2): 63-71
Type 3: 62-73
Ghia: 66-74
Thing: 73-74
Race/Off-Road: 66-79
No customer reviews for the moment.
Part #: 111105271RC
These flywheels have been reconditioned and are sold on an exchange basis.
Application:Part #: 311105273ACO
These flywheels have been reconditioned and are sold on an exchange basis.
Application:Part #: 1105255BK
This is a very nice pulley; the numbers are etched in and do not wear off.
Application:Part #: 111105235A
These are the shims that set the endplay of the distributor drive gear.
Application:Part #: 1105257
This is a billet, zinc plated crankshaft pulley bolt that has a 3/8" drive hole broached into the center.
Application:Part #: 1105277
Here are some flywheel pins that give you more contact surface on the flywheel.
Application:Part #: 111105209
CRANKSHAFT GEAR, timing, 36hp engines
Application:Part #: 1105253RD
This is a crank pulley for an upright motor.
Application:Part #: 1105279
This gasket is only used if you're having problems with your end play.
Application:Part #: 111105433
Wrist Pin Bushing.
Application:Bug (Type 1); 40hp
Bus (Type 2); 40hp
KG; 40hp
Part #: 1105253BK
This is a crank pulley for an upright motor.
Application:Part #: 111105271CO
Core
Application:Part #: 311105273AN
VW Flywheel, 200mm 12 volt 15-1600cc Engines
Application:Part #: 113105701
These are the shells that go in the rods and ride on the crank.
Application:Part #: 1105259
This is a chrome stock bolt and washer that holds the crankshaft pulley on.
Application:Part #: 113105281A
These shims set the endplay of the crankshaft.
Application:
These shims set the endplay of the crankshaft.
