Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
This seal goes around the front window. To remove the old glass, use a fixed-bladed knife. Stick the knife between the rubber and glass on the outside of the Bug. Now cut the rubber until you feel the point of the knife hit metal. Cut all the way around, until you have cut the rubber in half. Peel the rubber off and slowly push the glass out from the inside. Make sure someone is on the outside to catch the windshield. Install the new rubber with the seam on the top and in the middle. Do not use any kind of lubricant, as it will cause the glass to separate. Wrap a piece of 14 gauge wire in the groove that holds the window to the Bug, overlapping the ends on the bottom at the center. Clean the body area and do any repairs needed. We use dish soap as a lubricant, but only between the rubber and body metal, never between the rubber and the glass. Smear the soap from the lip to the outside edge. At this point, grab a friend to help you. Place the window in the Bug from the outside with the two ends of the wire inside the Bug. Push the window in until the rubber hits the lip. While your friend holds the glass in place from the outside, get into the Bug and pull one end of the wire a little one way and then the other wire a little the other way. Keep doing this until you reach the top. If you miss, push the window out and start over. After the first one youll be surprised how easy it is. If you have a lot of windows to do we offer a tool that makes it even easier. American style has groove for chrome.
Bug (Type 1): 73-79
No customer reviews for the moment.
Part #: 111837625B
Vent wing seals on the front doors keep out the elements.
Application:Part #: 1845201A
This kit comes with everthing you need to eliminate your vent window, tempered glass, felt window channels, inner and outer snap in scrappers.
Application:Part #: 113847125A
Popout window hinge
Application:Bug (Type 1); 50-77
Part #: 1845201SASHS
This kit comes with everthing you need to eliminate your vent window, tempered glass, felt window channels, inner and outer snap in scrappers.
Application:Part #: 113845321AAM
This seal goes around the side window that is stationary (does not have a frame).
Application:Part #: 151847321A
Quarter Window Hinge, Left, Convertibles only
Application:Part #: 111837501D
Window Regulator, Left
Application:Part #: 151847351B
These are wedge to seal the coners on the front door and quarter windows, where the metal frames meet the scrapers.
Application:Part #: 151871353A
This seal goes on the windshield post to seal the vent wing.
Application:Part #: 151847366A
Window Sash for Rear Quarter Window, Right, Convertible
Application:Part #: 111845101H
These are cut from safety glass as required by law.
Application:Part #: 111837471
Inner and Outer Window Scraper, Set of 4
Application:Part #: 113845521ACL
This seal is for the rear window.
Application:Part #: 141837563
Window Guide Rail Threaded Pin, Convertible only
Application:Part #: 113847135
These seals are for the side popout windows.
Application:Part #: 151847341A
This seal goes between the rear quarter window and the front door side window on a convertible.This is very important if you want to keep your window in..
Application:
