Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These are the metal brake lines found throughout the car.
These are the metal brake lines found throughout the car. We suggest you go buy a 11mm tubing wrench and a tubing bender before you start replacing lines. If you have an extra 11mm box end wrench, you can cut a slot in the box end which will allow you to slip it over the tube. When breaking the metal line loose from the brake hose, use a 17mm wrench on the hose and the 11mm wrench on the metal line. Once you have broken it free, remove the clip that holds the hose. When installing the new line, hand thread the nut into the brake hose and then install the clip and tighten. You will need to take out the driver's seat when replacing the front to rear line because it runs along the tunnel. Cut the old line in half. Unthread both ends, one at the master cylinder and the one at the rear union. Pull it out from the inside of the car. Now make the bends in the new line with the tubing bender using the old line as a pattern. Install the new line from the inside of the car starting with the front. Make sure you have grommets where the line goes through the firewalls. 1240mm/ 48.8"
No customer reviews for the moment.
Part #: 1105254BK
This is a crank pulley for an upright motor.
Application:Part #: 113857059
Trim around Fan Switch
Application:Part #: 111853695
Clip for Deck Lid Script (3 per kit)
Application:Part #: 6857646
Billet Foot Pegs, 1/2" X 20 Threads, Pair
Application:Part #: F1129601
These are the glues and oils we use..
Application:Part #: 251407629
This is the seal for the front wheels.
Application:Part #: 1601132CH
Lug Nut, 12 point, 12mm-1.5, Chrome set of 5
Application:Part #: 1615107E
Replacement Rear Brake Bracket for Kit # 1615108ADLX, 1615108DLX, 1615115, 1615115A, 1615116A, 1615116, 1615113HD, 1615110, Each
Application:Part #: 211941037C
Headlight Assembly, US Style, Clear Glass, Complete less bulbs, LEFT
Application:Part #: 111837267A
These are the stops on the check rods that prevent you from opening the doors too far.
Application:Part #: 211843436B
Side Sliding Door Upper Roller and Bracket
Application:Bus (Type 2); 68-79
Part #: 133201181A
Fuel Elbow, "T" to Main Exit
Application:Part #: 1857511
This mirror allows visibility of the whole rear area of your car.
Application:Part #: 111881407
Like the door panels, seat covers are a long subject; so here's the basics.
Application:Part #: 113857611EBK
This is a strap, not a handle.
Application:
These are the metal brake lines found throughout the car.