Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:These are the metal brake lines found throughout the car.
These are the metal brake lines found throughout the car. We suggest you go buy a 11mm tubing wrench and a tubing bender before you start replacing lines. If you have an extra 11mm box end wrench, you can cut a slot in the box end which will allow you to slip it over the tube. When breaking the metal line loose from the brake hose, use a 17mm wrench on the hose and the 11mm wrench on the metal line. Once you have broken it free, remove the clip that holds the hose. When installing the new line, hand thread the nut into the brake hose and then install the clip and tighten. You will need to take out the driver's seat when replacing the front to rear line because it runs along the tunnel. Cut the old line in half. Unthread both ends, one at the master cylinder and the one at the rear union. Pull it out from the inside of the car. Now make the bends in the new line with the tubing bender using the old line as a pattern. Install the new line from the inside of the car starting with the front. Make sure you have grommets where the line goes through the firewalls. 2760mm/108.6
No customer reviews for the moment.
Part #: 111698002
This kit has all the springs, pins and keepers for drum brakes.
Application:Part #: 6012903L
This pole has a light on the top of it, just above the flag.
Application:Part #: 6501205IRS
These plates are .250" thick, that means they can handle the abuse of off roading.
Application:Part #: 311012243
This is a slick tool for getting your hub caps off.
Application:Part #: 111255483
These are the vents that clip into the dash.
Application:Part #: 2863620B
This handy basket hangs from the vent slots to allow you to finally have the cup holder you've always dreamed of. The front spring loaded pocket is a nice place to store your cell phone, or maybe to hold your registration for when the cops pull you over for going too slow. Available in black and white.
Application:Part #: 6501280
Steel Axle Bearing Housing
Application:Part #: 251501203A
A new assembly consists of a new axle with CV joints and boots, ready to install.
Application:Part #: 113117021
This stock oil cooler cools the hot oil coming from the engine.
Application:Part #: 1119029
Remote coil mounts are used when you want to keep the coil on the motor, yet out of the way of down linkage on dual carburetors..
Application:Part #: 151871189F
The top staples to this front bow.
Application:Part #: 113823731B
This is the seal that goes on the body for the front hood to sit on.
Application:Part #: 211405670
Spindle Nut, Right
Application:Part #: 211813227
This is a repair panel for the area above the engine lid.
Application:Part #: 1401300A
If your stock bushings are worn out or you have an aluminum beam, we offer the following urethane bushings and replacements..
Application: