Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
Most people don't realize that these are one of the most important parts in the motor.
Most people don't realize that these are one of the most important parts in the motor. When a rod is reconditioned the cap is separated, the bolts taken out and the cap mating surfaces ground. The rod is then put back together now having an oval hole. This hole is then machined round again. The problems we have seen are; the boring of the hole and bushing being bored crooked, throwing the rod side ways when the cylinder fires. The other problem is that, if one rod has been reconditioned once and the others five times then one rod is a lot longer than the others, affecting the compression ratio. You might have compression ratios of 7.7 in 3 cylinders and 9.1 in one cylinder; the result is an unbalanced engine and major detonation in one cylinder. The rods we carry are checked for straightness, and weighed to within 10 grams and matched for length to .005. All rods are sold in sets on an exchange basis.
Bug (Type 1): 40hp-1300
Bus (Type 2): 40hp-1300
Type 3: 40hp-1300
Ghia: 40hp-1300
No customer reviews for the moment.
Part #: 111863404
This is a full carpet kit.
Application:Part #: 1129201301
48mm/51mm IDA Carb Float Only
Application:Part #: 411945235
This seal goes between the tail light housing and the body of the car..
Application:Part #: 1255105FCC
HD Flanged 1 1/2" heater boxes to run with your performance Engine & Exhaust, Left
Application:Part #: 211598200
Spring Plate Cover Hardware Kit
Application:Part #: 211259471
Air Vent Diffuser, Dashboard and Behind Rear Seats, Each
Application:Part #: 113415371
Steering box Pitman arm.
Application:Part #: 211721335B
This cable pulls the arm that releases the clutch.
Application:Part #: 1601129
Chrome Locking 14mm Bolts Set of 4 (Porsche Style)
Application:Part #: 141953166C
This seals the front turn signal housing from the fender.
Application:Part #: 1863515B
This plastic cover under the front hood, covers up all the wiring.
Application:Part #: 6425022
Billet Steering Damper Bracket to be used on Sand Buggies on Aftermarket Aluminum Link-Pin Front Axles
Application:Part #: 211601152
Stainless Steel Beauty Rings for 15" Stock wheels (Set of 4)
Application:Part #: 211707111J
Front Bumper, Primered
Application:Part #: 1601034
Fuchs Polished, 5x205, 15x5.5"
Application:Part #: 241853345
These chrome moldings for American style seals go around the windows and are just for looks.
Application:
Most people don't realize that these are one of the most important parts in the motor.