Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These are the metal brake lines found throughout the car.
These are the metal brake lines found throughout the car. We suggest you go buy a 11mm tubing wrench and a tubing bender before you start replacing lines. If you have an extra 11mm box end wrench, you can cut a slot in the box end which will allow you to slip it over the tube. When breaking the metal line loose from the brake hose, use a 17mm wrench on the hose and the 11mm wrench on the metal line. Once you have broken it free, remove the clip that holds the hose. When installing the new line, hand thread the nut into the brake hose and then install the clip and tighten. You will need to take out the driver's seat when replacing the front to rear line because it runs along the tunnel. Cut the old line in half. Unthread both ends, one at the master cylinder and the one at the rear union. Pull it out from the inside of the car. Now make the bends in the new line with the tubing bender using the old line as a pattern. Install the new line from the inside of the car starting with the front. Make sure you have grommets where the line goes through the firewalls.
Bus (Type 2): 55-67
No customer reviews for the moment.
Part #: 6129652BK
Outerwear pre-filters feature a patented; Micro Mesh nylon filtration system that stops sand and dirt before it gets to your air cleaner element.
Application:Part #: 2863621AL
Polished Aluminum Cup Holder
Application:Part #: 1701062
These pans will replace those rusted out parts of the front or rear floors.
Application:Part #: 111943191E
This is the lens and seal for the light that shines on the license plate.
Application:Part #: 111883401
Like the door panels, seat covers are a long subject; so here's the basics.
Application:Part #: 113707201B
This is the strip of rubber that goes on the center of the bumper..
Application:Part #: 211817810
This is the flat seal for the air duct on buses 1955-1967.
Application:Part #: 111105285
Flywheel Shim 25-36HP, .32mm (0.0125")
Application:Part #: 151847366A
Window Sash for Rear Quarter Window, Right, Convertible
Application:Part #: 111971225
This cable goes from the battery to the starter.
Application:Part #: 1601141FCH
Silver Center Cap with EMPI Logo, Cap Only
Application:Part #: 1903183
This aftermarket chrome cap nut and spacer hold the alternator/generator pulley on.
Application:Part #: 151871034
This is the outer skin on your convertible.
Application:Part #: 211809506B
The lower part of the dog leg.
Application:Part #: 1119525BK
This tin goes from one piece of cylinder tin to the other.
Application:Part #: T1129026
This meter is used for synchronizing your dual carburetors.
Application:
These are the metal brake lines found throughout the car.