Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
This kit contains a bushing, a clutch return spring and the retaining clips to install the throw-out bearing shaft in the transmission.
This kit contains a bushing, a clutch return spring and the retaining clips to install the throw-out bearing shaft in the transmission. The engine has to be pulled out in order to put the bushing on. Start by removing the throw-out bearing. Now take the clip off the cable arm and remove the arm. Go to the backside of the bellhousing and remove the 11mm bolt that sets the bushing. Push the shaft from the inside out towards the driver's side; this will push the bushing out. Now for the fun part, grease up the shaft where the bushing rides. Install the inner clip on the shaft, then install the shaft without the bushing. Slide the new bushing from the outside over the shaft, making sure that the indent hole lines up with the hole on the backside of the transmission. Install the alignment bolt in the bushing and then replace your throw-out bearing. Now replace the clutch return spring, the bell, and the clutch cable arm. Put on the clip. Don't try to put the spring over the arm until you have this outer clip on. Take a Phillips screwdriver and wrap it around the arm; hook the spring and pry it backward. This will install the spring back on the arm without you loosing your sanity or a finger.
Bug (Type 1): 61-72
Bus (Type 2): 61-67
Type 3: 61-72
Ghia: 61-72
Race/Off-Road: 61-72
No customer reviews for the moment.
Part #: N122412
This is a general rule for washer use, wafer washers are used against aluminum and lock washers are used against steel..
Application:Part #: 311141025C
The clutch cover is also known as a pressure plate.
Application:Part #: 113141723C
This spring returns the clutch arm.
Application:Part #: 1141025
Heavy Duty Clutch Pressure Plate - 1700lbs. This is made by KEP
Application:Part #: 111141719F
Clutch Cable Arm Forged for 20mm Cross shaft
Application:Part #: 1141030
200mm 6 puck Clutch Disc
Application:Part #: 311141031D
This disc transfers the power from the motor to the transmission.
Application:Part #: 111141031E
This disc transfers the power from the motor to the transmission.
Application:Part #: 1141701A
This heavy duty arm is a good idea if you need a new clutch arm.
Application:Part #: 111141723A
Return Spring For Cross Shaft
Application:Part #: 111141165A
Also known as a throw-out bearing, this bearing's function is to disengage the clutch.
Application:Part #: 1141024
These are hardend bolts, 10.9 instead of the stock 8.8.
Application:Part #: N102401
This is a list of the most common bolts used on a car..
Application:Part #: 131141719HDL
Clutch Cable Arm Forged for 16mm Cross shaft
Application:Part #: 113141701C
This shaft holds the throw-out bearing in place.
Application:Part #: 211141025A
Clutch Cover, 12 volt 200mm, 9 spring
Application:
This kit contains a bushing, a clutch return spring and the retaining clips to install the throw-out bearing shaft in the transmission.