Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:This hydraulic cylinder feeds all the wheel cylinders.
This hydraulic cylinder feeds all the wheel cylinders. After installing a new one make sure the rod that pushes the plunger is adjusted correctly. When adjusting it you can't see the measurement but you can feel it. The rod should have about an 1/8" of free play before it starts pushing. If it's too tight it will not allow the fluid to travel back to the reservoir locking up the brakes usually in the middle of an intersection.
No customer reviews for the moment.
Part #: 113611817A
This is the grommet for the reservoir line(s) where they go into the master cylinder.
Application:Part #: 281611349
This cap sits on the top of the brake fluid reservoir filler hole.
Application:Part #: 211611741K
These are the metal brake lines found throughout the car.
Application:Part #: 803611755
These are the metal brake lines found throughout the car.
Application:Part #: 211611775B
This flex hose goes from the metal brake line on the rear fork to the metal brake line on the axle tube.
Application:Part #: 113611775E
This flex hose goes from the metal brake line on the rear fork to the metal brake line on the axle tube.
Application:Part #: 311611701B
This flex hose goes from the metal brake line to the front wheel cylinder. m/f 335mm
Application:Part #: 113611301L
The reservoir holds the brake fluid for the brake master cylinder.
Application:Part #: 113611195
This boot is on the plunger end of the master cylinder, keeping dirt out of the master cylinder..
Application:Part #: 211843419
Front lower, Bearing, Sliding Door
Application:Part #: JC22340
Jaycee Fuel Pump Block off w/ 3/8" Breather, Black
Application:Part #: 1115183RD
This plate is made out of a solid piece of aluminum. Red
Application:Part #: 211813227B
This is a repair panel for the area above the engine lid.
Application:Part #: 211837235AIV
This plastic "donut" goes under the window crank or door handle to prevent the door panel from getting ripped.
Application:Part #: 151863123
These are the interior panels.
Application:Part #: 113863509B
Front Trunk Liner
Application:Part #: 1105253RD
This is a crank pulley for an upright motor.
Application:Part #: 111129493A
Steel Vacuum Line junction between Vacuum Advance and carburetor
Application:Part #: 113301185A
This kit contains all of the gaskets needed to rebuild a transmission.
Application:Part #: 211615107ACO
Front calipers hold the brake pads that stop the rotor, which in turn stops your vehicle.
Application:Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 151871409A
Rear Bow Base Seal for Convertible Top
Application:Part #: 151871030
This is the outer skin on your convertible.
Application:Part #: 211498211CWG
These spindles have reconditioned king pins and are ready to bolt back on. They do NOT come with link pins, so look at yours to see if you need new ones. Most of the time you do not need new ones as they are a bearing and not a bushing. Due to the core shortage on these spindles you will need to send us your old ones first.
Application:Part #: 6857051A9
These boxes can hold all your gauges, switches etc.
Application: