Engine Bolts - Starter side, manual trans, half moon style

Part #: 113101157C

Cam Plug - Ridged style

This plug goes in the back of the case (flywheel side).

Bug (Type 1): 1300-1600
Bus (Type 2): 1300-1600
Type 3: 1300-1600
Ghia: 1300-1600
Thing: 1300-1600
Race/Off-Road: 1300-1600

Part #: 113105245FRS

Rear Main Seal, Double Lipped

Rear Main Seal, Double Lipped

Bug (Type 1): 61-79

Bus (Type 2): 60-71

Type 3: 62-73

Ghia: 61-74

Thing: 73-74

Offroad: 61-79

Race: 61-79

Part #: 113115475

Alternator-Generator Stand - Filler gasket

It's possible to put a generator on an alternator stand but not the other way around.

Bug (Type 1): 61-74
Bus (Type 2): 56-71
Type 3: All
Ghia: 61-74
Thing: 73-74
Race/Off-Road: All

Part #: 111198001

Engine Gasket Set, 25 HP

Engine Gasket Set, 25 HP

Bug (Type 1): 25-36 HP

Part #: 043101129

Case Half Washers and Nuts - Washer

This is the washer used under the nuts on cases that use an o-ring on the center main studs.

Bug (Type 1): 1500-1600
Bus (Type 2): 1500-1600
Type 3: 1500-1600
Ghia: 1500-1600
Thing: 1500-1600
Race/Off-Road: 1500-1600

Part #: 1101131B

Case Head Stud Case Savers - 10mm ID x 14mm OD, each

A case saver is an insert that repairs worn or stripped head stud holes in a case.

Bug (Type 1): All
Bus (Type 2): -71
Type 3: All
Ghia: All
Thing: All
Race/Off-Road: All

Part #: 111115421

Oil Relief Valve Spring 25-36 HP

Oil Relief Valve Spring 25-36 HP

Bug (Type 1): 25-36 HP

Part #: 1115431

Case Relief Plug - Hex size 22mm (pr)

This hex drive replacement plug is for the case relief spring(s).

Bug (Type 1): 40hp-1600
Bus (Type 2): 40hp-1600
Type 3: 40hp-1600
Ghia: 40hp-1600
Thing: 40hp-1600
Race/Off-Road: 40hp-1600

Part #: 1101031

Engine Hardware Kit - For 10mm head studs, Dual Port

Included in this kit are the bolts, nuts and washers required for "out to head" assembly of the engine..

Bug (Type 1): 1600
Bus (Type 2): 1600
Type 3: 1600
Ghia: 1600
Thing: 1600
Race/Off-Road: 1600

Part #: 1101131

Case Head Stud Case Savers - 10mm ID x 14mm OD, (8)

A case saver is an insert that repairs worn or stripped head stud holes in a case.

Bug (Type 1): All
Bus (Type 2): -71
Type 3: All
Ghia: All
Thing: All
Race/Off-Road: All

Part #: 113101219

Alternator-Generator Stand - gasket

It's possible to put a generator on an alternator stand but not the other way around.

Bug (Type 1): 40hp-1600
Bus (Type 2): 40hp-1600
Type 3: 40hp-1600
Ghia: 40hp-1600
Thing: 40hp-1600
Race/Off-Road: 40hp-1600

Part #: 1101132

Case Head Stud Case Savers - 8mm ID x 14mm OD, (16)

A case saver is an insert that repairs worn or stripped head stud holes in a case.

Bug (Type 1): All
Bus (Type 2): -71
Type 3: All
Ghia: All
Thing: All
Race/Off-Road: All

Part #: 1115107

Slip-in Windage Tray - 1600

This tray keeps the oil in the engine case from moving around too much, reducing oil starvation.

Bug (Type 1): All
Type 3: All
Ghia: All
Thing: All
Race/Off-Road: All

Part #: 1115422

Oil Pressure Boost Springs - Dual relief case

These stronger springs were designed to boost the oil pressure in your motor.

Bug (Type 1): 71-79
Bus (Type 2): 71
Type 3: 71-74
Ghia: 71-74
Thing: 73-74
Race/Off-Road: 71-

Part #: 113101221B

Alternator-Generator Stand - Deflector

It's possible to put a generator on an alternator stand but not the other way around.

Bug (Type 1): 1500-1600
Bus (Type 2): 1500-1600
Ghia: 1500-1600
Thing: 1500-1600
Race/Off-Road: 1500-1600

Part #: 1115139

Oil Fittings Brass - Oil passage plug 3/8" pipe

When plumbing the oil filter, oil cooler and/or case, these are the fittings you will need.

Bug (Type 1): All
Bus (Type 2): All
Type 3: All
Ghia: All
Thing: All
Race/Off-Road: All