Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
When mounting the oil cooler above the transmission on a Bug, Type 3, Ghia, Thing, or Off Road car you can use these rubber mounted studs.
When mounting the oil cooler above the transmission on a Bug, Type 3, Ghia, Thing, or Off Road car you can use these rubber mounted studs. Using these special studs spaces the cooler off the deck and allows air to pass through the oil cooler. You will need four of these studs to mount your cooler correctly. Note: Never mount an oiler cooler flush with the deck, doing so would not allow the air to flow through the cooler and the heat to properly dissipate. On a Bus, when mounting the oil cooler in the frame members you can use this rubber mounted stud. Using these special studs spaces the cooler off the deck and allows air to pass through the oil cooler. You will need two of these studs to mount your cooler correctly. We mount the front of the cooler flush with one of the floor frame members and the back spaced down about an inch (the thickness of this mounting stud). Note: Never mount an oil cooler flush with the deck on both sides. Doing so would not allow the air to flow through the cooler and the heat to properly dissipate.
Bug (Type 1): All
Type 3: All
Ghia: All
Thing: All
Race/Off-Road: All
No customer reviews for the moment.
Part #: 113115181A
This is the plate on the bottom of the motor.
Application:Part #: 1115449BL
Replacement Oil Cap Billet Blue
Application:Part #: N122412
This is a general rule for washer use, wafer washers are used against aluminum and lock washers are used against steel..
Application:Part #: 1115467HO
This is a breather box that will give excess "blow by" a place to go.
Application:Part #: 1117012
These bolt on mounts allow you to bolt the filter adapter under the driver's side fender or hang it off the exhaust flange..
Application:Part #: 111115111B
The oil pump is the heart of the engine, so it is very important to choose the right one.
Application:Part #: 1117108ALF
These fittings are used for the stainless steel hose.
Application:Part #: 113117303
This stock oil cooler cools the hot oil coming from the engine.
Application:Part #: 1117011
These bolt on mounts allow you to bolt the filter adapter under the driver's side fender or hang it off the exhaust flange..
Application:Part #: 1115107FF
30mm Oil pump for Dual Relief & Flat cam Full Flowed Engines
Application:Part #: 1115422
These stronger springs were designed to boost the oil pressure in your motor.
Application:Part #: 1115457BL
The smooth flow design has a nice look and comes with a knurled cross-groove or smooth billet grooved cap for a good grip when it is wet or oily. Blue
Application:Part #: 1115464
This air filter is made to protect the crankcase.
Application:Part #: JC22230
Jaycee Billet Oil Cap with Breater -8 AN Fitting, Blue
Application:Part #: N110085
Some of the more common nuts you might need..
Application:Part #: 1115141
This oil pump cover comes with a threaded boss.
Application:
When mounting the oil cooler above the transmission on a Bug, Type 3, Ghia, Thing, or Off Road car you can use these rubber mounted studs.
