Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
When mounting the oil cooler above the transmission on a Bug, Type 3, Ghia, Thing, or Off Road car you can use these rubber mounted studs.
When mounting the oil cooler above the transmission on a Bug, Type 3, Ghia, Thing, or Off Road car you can use these rubber mounted studs. Using these special studs spaces the cooler off the deck and allows air to pass through the oil cooler. You will need four of these studs to mount your cooler correctly. Note: Never mount an oiler cooler flush with the deck, doing so would not allow the air to flow through the cooler and the heat to properly dissipate. On a Bus, when mounting the oil cooler in the frame members you can use this rubber mounted stud. Using these special studs spaces the cooler off the deck and allows air to pass through the oil cooler. You will need two of these studs to mount your cooler correctly. We mount the front of the cooler flush with one of the floor frame members and the back spaced down about an inch (the thickness of this mounting stud). Note: Never mount an oil cooler flush with the deck on both sides. Doing so would not allow the air to flow through the cooler and the heat to properly dissipate.
Bug (Type 1): All
Bus (Type 2): All
Type 3: All
Ghia: All
Thing: All
Race/Off-Road: All
No customer reviews for the moment.
Part #: 1115456
The smooth flow design has a nice look and comes with a knurled cross-groove or smooth billet grooved cap for a good grip when it is wet or oily.
Application:Part #: 1117101
When plumbing the oil filter, oil cooler and/or case, these are the fittings you will need.
Application:Part #: 113117021
This stock oil cooler cools the hot oil coming from the engine.
Application:Part #: 1117104ALM
These fittings are used for the stainless steel hose.
Application:Part #: 1117111
When plumbing the oil filter, oil cooler and/or case, these are the fittings you will need.
Application:Part #: 113115181A
This is the plate on the bottom of the motor.
Application:Part #: 1117023FAN
This is the same as the mesa cooler but with a fan mounted to it.
Application:Part #: 1117011
These bolt on mounts allow you to bolt the filter adapter under the driver's side fender or hang it off the exhaust flange..
Application:Part #: N122412
This is a general rule for washer use, wafer washers are used against aluminum and lock washers are used against steel..
Application:Part #: 1115457
The smooth flow design has a nice look and comes with a knurled cross-groove or smooth billet grooved cap for a good grip when it is wet or oily.
Application:Part #: JC21030
Jaycee Mag-Plate, 6 Bolt, Blue
Application:Part #: 1115106A
This is a great way to increase the oil capacity of your engine.
Application:Part #: 021117151A
This stock oil cooler cools the hot oil coming from the engine.
Application:Part #: N110623
Some of the more common nuts you might need..
Application:Part #: N110062
Some of the more common nuts you might need..
Application:Part #: 1115449RD
Replacement Oil Cap Billet Red
Application:
When mounting the oil cooler above the transmission on a Bug, Type 3, Ghia, Thing, or Off Road car you can use these rubber mounted studs.
