Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:This kit contains a quality urethane bushing, a clutch return spring and retaining clips needed to install the throw-out bearing arm in the transmission.
This kit contains a quality urethane bushing, a clutch return spring and retaining clips needed to install the throw-out bearing arm in the transmission. The engine has to be pulled out in order to put the bushing on. Start by removing the throw out bearing. Now take the clip off the cable arm and remove the arm. Go to the backside of the bellhousing and remove the 11mm bolt that sets the bushing. Push the arm from the inside out towards the driver's side; this will push the bushing out. Now for the fun part, grease up the arm where the bushing rides. Install the inner clip on the arm, then install the arm without the bushing. Slide the new bushing from the outside over the arm, making sure that the indent hole lines up with the hole on the backside of the transmission. Install the alignment bolt in the bushing and then replace your throw-out bearing. Now replace the clutch return spring, the bell, and the clutch cable arm. Put on the clip. Don't try to put the spring over the arm until you have this outer clip on. Take a Phillips screwdriver and wrap it around the arm; hook the spring and pry it backward. This will install the spring back on the arm without you loosing your sanity or a finger.
Bug (Type 1): 73-79
Bus (Type 2): 76-79
Type 3: 73-74
Ghia: 73-74
Thing: 73-74
Race/Off-Road: 73-
No customer reviews for the moment.
Part #: 113141723C
This spring returns the clutch arm.
Application:Part #: 311141025E
The clutch cover is also known as a pressure plate.
Application:Part #: 113141181B
Guide Sleeve
Application:Part #: 1141033
Cushion Clutch Disc - 200mm
Application:Part #: 113198026
This kit contains a bushing, a clutch return spring and the retaining clips to install the throw-out bearing shaft in the transmission.
Application:Part #: 111141177AS
These clips hold the throw-out bearing to the arm.
Application:Part #: 1141027
Kennedy Stage 3 Pressure plate 2600 LB
Application:Part #: 211141025D
The clutch cover is also known as a pressure plate.
Application:Part #: 1141028
Kennedy Stage 4, 3000 LB Pressure Plate
Application:Part #: N122412
This is a general rule for washer use, wafer washers are used against aluminum and lock washers are used against steel..
Application:Part #: 113141165B
Also known as a throw-out bearing, this bearing's function is to disengage the clutch.
Application:Part #: 211141025A
Clutch Cover, 12 volt 200mm, 9 spring
Application:Part #: 131141719HDL
Clutch Cable Arm Forged for 16mm Cross shaft
Application:Part #: 1198026
This kit contains a quality brass bushing, a clutch return spring and retaining clips needed to install the throw-out bearing arm in the transmission.
Application:Part #: 113141701F
This shaft holds the throw-out bearing in place.
Application:Part #: 361141719HD
Clutch Cable Arm Forged for 20mm Cross shaft
Application: