Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These shims set the endplay of the crankshaft.
These shims set the endplay of the crankshaft. It is very important that you get this right. The endplay should be between .003" and .005". Too loose and you will beat out the rear main bearing, too tight and the flywheel will try to grab the rear main bearing and spin it. If you are going to use old shims, make sure they are not cupped. Flex them one by one to see if they pop; if they do, they're cupped. Note: The way to set the endplay is to leave out the flywheel seal and o-ring. Find three .010" shims; install the three shims and bolt on the flywheel. Torque the flywheel to 250 ft. lb. Using a dial indicator mounted on the flywheel with the needle against the case, push the flywheel back and forth to get a reading. If you have too little or too much then take the flywheel off and figure out what you need to add or subtract to come up with the correct endplay. You may need to take out a shim(s) and add a thicker one(s). You must have a total of three shims; no more no less. After you get the correct thickness, install the seal and o-ring.
Bug (Type 1): 66-79
Bus (Type 2): 63-71
Type 3: 62-73
Ghia: 66-74
Thing: 73-74
Race/Off-Road: 66-79
No customer reviews for the moment.
Part #: 113105249
This key holds the oil deflector in place as well as aligns the front pulley.
Application:Part #: 311105431A
Wrist Pin Bushing.
Application:Bug (Type 1); 1300-1600
Bus (Type 2); 1300-1600
Type 3; 1300-1600
KG; 1300-1600
Thing: 1300-1600
Offroad/Race; 1300-1600
Part #: 1105305
This washer is larger in diameter than stock so it gives you more surface coverage over the dowel pins.
Application:Part #: 113105401ARC
Most people don't realize that these are one of the most important parts in the motor.
Application:Part #: 113105281A
These shims set the endplay of the crankshaft.
Application:Part #: JC86070
Jaycee Billet 7" Crank Pulley for Street Cars, Silver
Application:Part #: 113105231B
This gear matches up with the brass gear that is on the crank.
Application:Part #: 111105283
Flywheel Shim 25-36HP, .30mm (0.012")
Application:Part #: 211105271CRC
These flywheels have been reconditioned and are sold on an exchange basis. This is a rare flywheel so I do not have any in stock. You will need to send in yours first and we can recondition it.
Application:Part #: 1105255BK
This is a very nice pulley; the numbers are etched in and do not wear off.
Application:Part #: 113105245FS
This seal goes behind the flywheel.
Application:Part #: 113105271BRC
These flywheels have been reconditioned and are sold on an exchange basis. Currently out of stock of cores. MUST send core before we can ship flywheel.
Application:Part #: 111105271RC
These flywheels have been reconditioned and are sold on an exchange basis.
Application:Part #: 1105305R
This is a large thrust surfaced gland nut made out of chromoly.
Application:Part #: 1105169F
Forged 69mm Counter Weighted Crankshaft
Application:Part #: 111903137S
Replacement Belt for Serpentine System
Application:
These shims set the endplay of the crankshaft.
