Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
This seal goes behind the flywheel.
This seal goes behind the flywheel. It should be replaced every time the flywheel is taken off. If your seal is leaking, take the flywheel off and pry the seal out. Now remove the shims and call a friend. Have your friend push and then pull the front pulley while you look at the rear main bearing. If the bearing is moving, a new seal will not solve your problem. The engine will have to be taken apart and the case will need to be machined. If it is not moving, then you will want to check your endplay before installing the new seal. See CRANKSHAFT ENDPLAY SHIMS for instructions on how to do this. Install the seal and make sure it's all the way in (about 1/16" past flush). If you do not have a flywheel seal installer, turn your old seal upside down and use it to drive the new one in using a hammer. Note: The endplay (amount the crank is allowed to move back and forth) is .003" to .005". This measurement is very important if you want the engine to last.
Bug (Type 1): 46-60
Bus (Type 2): 50-59
Ghia: 56-60
No customer reviews for the moment.
Part #: 113105231B
This gear matches up with the brass gear that is on the crank.
Application:Part #: 111105287
Flywheel Shim 25-36HP, .34mm (0.0135")
Application:Part #: 1903108RD
EMPI Serpentine Belt System Red
Application:Part #: 311105431A
Wrist Pin Bushing.
Application:Bug (Type 1); 1300-1600
Bus (Type 2); 1300-1600
Type 3; 1300-1600
KG; 1300-1600
Thing: 1300-1600
Offroad/Race; 1300-1600
Part #: 1105174
This crankshaft is made of E4340 chromoly forging, one of the strongest metals known to man.
Application:Part #: 111105281
Flywheel Shim 25-36HP, .24mm (0.01")
Application:Part #: 113105251G
This pulley on the end of the crank turns the fan belt.
Application:Part #: 1105255BK
This is a very nice pulley; the numbers are etched in and do not wear off.
Application:Part #: 111105719A
Rod Bearings .30
Application:Part #: 1105401B
These connecting rods are longer than stock.
Application:Part #: 111105305E
It's really a bolt, but that's what everybody calls it.
Application:Part #: 1105253RD
This is a crank pulley for an upright motor.
Application:Part #: 1105278
Here are some flywheel pins that give you more contact surface on the flywheel.
Application:Part #: 113105401ARC
Most people don't realize that these are one of the most important parts in the motor.
Application:Part #: 113105401ACO
Most people don't realize that these are one of the most important parts in the motor.
Application:Part #: 1105251CH
This is a stock pulley that has been chromed.
Application:
This seal goes behind the flywheel.
