Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These are the shells that go in the rods and ride on the crank.
These are the shells that go in the rods and ride on the crank. To determine the size you need, mic the crank on the rod journal; 2.165 to 2.164 is standard, 2.155 to 2.154 is .010 over, 2.145 to 2.144 is .020 over and 2.135 to 2.134 is .030 over. We don't like to run a crank over a .030 undersize as the bearings are too thick. Note: When installing the bearings try not to touch the surface that the crank rides on with your fingers until you spread oil on it. Grab it by the edges and push it into place. Never oil the surface that sits in the rod, oil goes on the crank side. We use 30W oil, not grease. Make sure that the two locating tabs face each other when installing them and that the tang on the rod beam is up for that cylinder. The total torque is 28 ft. lb. starting at 15 ft. lb. When you're done torquing the rods, make sure they spin freely. If they don't, take the rod off and find out what's restricting it. Note: IT WON'T WEAR IN; IT WEARS OUT.
No customer reviews for the moment.
Part #: 311105273ACO
These flywheels have been reconditioned and are sold on an exchange basis.
Application:Part #: JC86070
Jaycee Billet 7" Crank Pulley for Street Cars, Silver
Application:Part #: 1105251ALRD
Aluminum Stock Crankshaft Pulley Red
Application:Part #: 1105182
This crankshaft is made of E4340 chromoly forging, one of the strongest metals known to man.
Application:Part #: 1105257
This is a billet, zinc plated crankshaft pulley bolt that has a 3/8" drive hole broached into the center.
Application:Part #: 111105401CO
Most people don't realize that these are one of the most important parts in the motor.
Application:Part #: 1105279
This gasket is only used if you're having problems with your end play.
Application:Part #: 111105235A
These are the shims that set the endplay of the distributor drive gear.
Application:Part #: 1105178
This crankshaft is made of E4340 chromoly forging, one of the strongest metals known to man.
Application:Part #: 111105313A
It's really a bolt, but that's what everybody calls it.
Application:Part #: 1105277
Here are some flywheel pins that give you more contact surface on the flywheel.
Application:Part #: 1105271
If your are going to run a 69mm or a 78 mm counterweighted crank, then you will want to have your flywheel 8 doweled or get a flywheel has been 8 doweled.
Application:Part #: 1105273BR
Lightened 12 lb.
Application:Part #: 1105401AC
These connecting rods are longer than stock.
Application:Part #: 113105271BRC
These flywheels have been reconditioned and are sold on an exchange basis. Currently out of stock of cores. MUST send core before we can ship flywheel.
Application:Part #: 113105701
These are the shells that go in the rods and ride on the crank.
Application:
These are the shells that go in the rods and ride on the crank.
