Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N203551F
These are new hoses that are more resistant to Ethanol, meaning they last longer. This type of hose is what we now recommend.
Application:
These are the shells that go in the rods and ride on the crank.
These are the shells that go in the rods and ride on the crank. To determine the size you need, mic the crank on the rod journal; 2.165 to 2.164 is standard, 2.155 to 2.154 is .010 over, 2.145 to 2.144 is .020 over and 2.135 to 2.134 is .030 over. We don't like to run a crank over a .030 undersize as the bearings are too thick. Note: When installing the bearings try not to touch the surface that the crank rides on with your fingers until you spread oil on it. Grab it by the edges and push it into place. Never oil the surface that sits in the rod, oil goes on the crank side. We use 30W oil, not grease. Make sure that the two locating tabs face each other when installing them and that the tang on the rod beam is up for that cylinder. The total torque is 28 ft. lb. starting at 15 ft. lb. When you're done torquing the rods, make sure they spin freely. If they don't, take the rod off and find out what's restricting it. Note: IT WON'T WEAR IN; IT WEARS OUT.
No customer reviews for the moment.
Part #: 111105433
Wrist Pin Bushing.
Application:Bug (Type 1); 40hp
Bus (Type 2); 40hp
KG; 40hp
Part #: 1105258
This is a stock, zinc-plated crankshaft pulley bolt that has a 3/8" drive hole broached into the center.
Application:Part #: 111105263A
The bolt that holds the crankshaft pulley on.
Application:Part #: 211105271CRC
These flywheels have been reconditioned and are sold on an exchange basis. This is a rare flywheel so I do not have any in stock. You will need to send in yours first and we can recondition it.
Application:Part #: 1105255BK
This is a very nice pulley; the numbers are etched in and do not wear off.
Application:Part #: 1903108BLU
EMPI Serpentine Belt System Blue
Application:Part #: 111105223
This brass gear goes on the crank to turn the distributor drive shaft.
Application:Part #: 113105281A
These shims set the endplay of the crankshaft.
Application:Part #: 1105305
This washer is larger in diameter than stock so it gives you more surface coverage over the dowel pins.
Application:Part #: 1105277
Here are some flywheel pins that give you more contact surface on the flywheel.
Application:Part #: 111105713A
Rod Bearings .20
Application:Part #: 1105251ALBL
Aluminum Stock Crankshaft Pulley Blue
Application:Part #: 1105401A
These connecting rods are longer than stock.
Application:Part #: 111105313A
It's really a bolt, but that's what everybody calls it.
Application:Part #: JC86040
Jaycee Billet 7" Crank Pulley for Street Cars, Red
Application:Part #: 1105253BK
This is a crank pulley for an upright motor.
Application:
These are the shells that go in the rods and ride on the crank.
