Part #: N109051
Side Popout Window Frame Screws (3.5mmX6mm) Frame to Hinge
Screws for replacement pop out window frame to hinge
Application:- Bus (Type 2): -67
Part #: N109051
Screws for replacement pop out window frame to hinge
Application:Part #: N139681
This is a list of the most common screws you might need..
Application:Part #: N185164
Screws for replacement pop out window Latches to Body
Application:Part #: 211837659
This nylon washer goes on the wing bolt keeping the bolt from chewing up the slide on the safari window. Washers sold individually 8 are required for Front Safaris and 4 are required for Rear Safaris.
Application:Part #: N107101
This is a list of the most common screws you might need..
Application:Part #: N141212
These are the latches that hold the popout frame out.
Application:Wolfgang Billet Valve Covers There are a few companys making billet valve covers and I have used a few of them and liked them. But we decided to make our own with a few differences.
There are a few companys making billet valve covers and I have used a few of them and liked them. But we decided to make our own with a few differences.
Each cover is made out of a solid chunk of aluminum. We went to great lengths to get them centered on the heads. Rocker stands vary, so we got them as close as possible on a stock casting head. We used a thick o-ring material for a good seal. By using an o-ring you can take them on an off a lot without having to replace a gasket. Most applications of this type of valve cover is going to be on race engines that need a breather vent, so we made the -8AN fitting right into the cover. The outer edge of the cover we radius as much as we could to make as much room as possible for any body clearance issues. Putting these on a stock bug engine will more than likely still require some body clearancing . On the seals for the bolts we are using a
tubular seal instead of just a small o-ring. We just feel its easier to deal with when taking them on and off. They come in any color you like as long as its black.
Intro price of $269.95 per set
No customer reviews for the moment.
Part #: 1109398
These rocker studs are much stronger than the stock studs and are .100" longer to allow more flexibility when setting your rocker arm geometry..
Application:Part #: 1198092BWCH
92mm Pistons & Cylinders Thick Wall set with a 82mm Stroke CHINA
Application:Part #: 1198162
These rings are cast iron.
Application:Part #: 1101383
Whether your motor lives or not can depend upon this little shim.
Application:Part #: 1198090BCH
90.5mm Pistons & Cylinders - 82mm Stroke CHINA
Application:Part #: 113101353ECO
All of our rebuilt cylinder heads are built from non-cracked or non-welded head cores (rebuilt welded heads will usually crack again next to the weld).
Application:Part #: 021101457
These nuts and washers hold the heads on.
Application:Part #: 1198083
All kits come with pistons, cylinders, rings, wrist pins and clips.
Application:Part #: 1101355MP
Here's another long subject, but it'll give you a little something to think about.
Application:Part #: 111198057
These come in sets of four pistons with rings, four cylinders, four wrist pins and eight wrist pin keepers.
Application:Part #: 1101393
Whether your motor lives or not can depend upon this little shim.
Application:Part #: 1198090A
All kits come with pistons, cylinders, rings, wrist pins and clips.
Application:Part #: 1101342
36 HP Barrel Shims .020 (4)
Application:Part #: 113101353BRB
All of our rebuilt cylinder heads are built from non-cracked or non-welded head cores (rebuilt welded heads will usually crack again next to the weld). Due to a shortage of cores we will need your Cylinder head Cores before sending any Rebuilt heads.
Application:Part #: 043101457
These nuts and washers hold the heads on.
Application:Part #: 111101481
This gasket goes between the valve cover and the head.
Application: